No. 60 is only a steel with good joint.
Title: high steel
: 60
: GB/T
: S58C
: C60(1.0601),CK60(1.1221),Cm60(1.1223)
Us : 1060
● and scale:
No. 60 steel for and are very high, cold is low, poor poor and water crack large of .No.60 steel is used for coil, wheel cams, steel rope and other large under the of wear and parts.
Scope of Mold
It is the rod of steel with good joint for air cast such as ICD5, and so on.It can also be used in hard to the and parts of the car sheet metal cover die and large metal sheet metal die.
In there are also some to pay to when using:
1. Dry the at °C for 30-50 in a wet place.
2. it is above 200°C, and after . Maybe it is to apply .
3. is and is used as the base to .
HRC 48-52 Cr Si Mn C
scale:
and m/ M 3.2*350mm 4.0*350mm
scale (Amp)
No. 60
● (%) :
C: 0.57 ~ 0.65
Si: 0.17 ~ 0.37
Mn: 0.50 ~ 0.80
S: 0.035 or less
P P: 0.035 or less
Cr: 0.25 or less
Ni Ni: 0.25 or less
Cu: 0.25 or less
60号钢，是仅有接合性较好之中硬度钢焊条。资料称号：优质碳素结构钢商标：60规范：GB/T 对应日本商标：S58C对应德国商标：C60(1.0601),CK60(1.1221),Cm60(1.1223)对应美国商标：1060●特性及适用规模：60号钢为亚共析钢，强度、硬度和弹性都很高，冷变形时塑性较低，切削性较差，焊接和淬透性差，水淬有发生裂纹倾向，大型制件多选用正火。60号钢用于制造轴、弹簧圈、轮轴、各种垫圈、凸轮、钢绳等受力较大、在冲突条件下作业，要求较高强度、耐磨性和必定弹性的零件。模具修补范畴它是仅有接合性较好之中硬度钢焊条，适用于空冷钢、铸钢：如ICD5、等等。轿车板金掩盖件模具及大型五金板金冲压模具之拉延、拉伸部位修补，也可用于硬面制造。另外在使用时也有一些需求留意的：1. 于湿润场所施工前，焊条先以°C烘干30-50分钟。2. 一般施以200°C以上预热，焊接后空冷，或许的话最好施行应力消除。3. 需多层堆焊处，以打底，可得到较好的焊接作用。硬度 HRC 48-52首要成份 Cr Si Mn C适用电流规模：直径及长度m/m 3.2*350mm 4.0*350mm电流规模（Amp） 号钢化学成分●化学成份（%）：碳 C ：0.57～0.65硅 Si：0.17～0.37锰 Mn：0.50～0.80硫 S ：≤0.035磷 P ：≤0.035铬 Cr：≤0.25镍 Ni：≤0.25铜 Cu：≤0.25
身份证未认证
营业执照已认证