一、属于锅炉用钢板，主要用于制作固定锅炉、船体锅炉及其他锅炉重要附件。 执行ASTM技术标准钢板，河南舞阳钢铁保性能钢板，一般厚度需要大于8个厚以上才能在舞阳钢铁公司定轧交货
钢种：S压力容器用中、低强度碳素钢板。SA285系列牌号有：、、执行标准：/，美国材料与试验协会标准。二、钢板通常以轧制状态交货，也可以按止火或消除应力处理或正火加消除应力处理状态订货。交货状态：热轧、控轧、正火、高温回火等；探伤、厚度方向性能要求、高强度高韧性要求等钢板。三、五大元素含量对钢板性能影响：a、碳（C）：钢中含碳量增加，屈服点和抗拉强度升高，但塑性和冲击性降低，当碳量0.23%超过时，钢的焊接性能变坏，因此用于焊接的低合金结构钢，含碳量一般不超过0.20%。碳量高还会降低钢的耐大气腐蚀能力，在露天料场的高碳钢就易锈蚀；此外碳能增加钢的冷脆性和时效敏感性。 b、硅（Si）：在炼钢过程中加硅作为还原剂和脱氧剂，所以镇静钢含有0.15－0.30%的硅。如果钢中含硅量超过0.50-0.60%,硅就算合金元素。硅能显著提高钢的弹性极限，屈服点和抗拉强度，故广泛用于作弹簧钢。在调质结构钢中加入1.0－1.2%的硅，强度可提高15－20%。硅和钼、钨、铬等结合，有提高抗腐蚀性和抗氧化的作用，可制造耐热钢。含硅1－4%的低碳钢，具有极高的导磁率，用于电器工业做矽钢片。硅量增加，会降低钢的焊接性能。c、锰（Mn）：在炼钢过程中，锰是良好的脱氧剂和脱硫剂，一般钢中含锰0.30－0.50%。在碳素钢中加入0.70%以上时就算“锰钢”，较一般钢量的钢不但有足够的韧性，且有较高的强度和硬度，提高钢的淬性，改善钢的热加工性能，如16Mn钢比A3屈服点高40%。含锰11－14%的钢有极高的耐磨性，用于挖土机铲斗，球磨机衬板等。锰量增高，减弱钢的抗腐蚀能力，降低焊接性能。 d、磷（P）：在一般情况下，磷是钢中有害元素，增加钢的冷脆性，使焊接性能变坏，降低塑性，使冷弯性能变坏。因此通常要求钢中含磷量小于0.045%，优质钢要求更低些。 e、硫（S）：硫在通常情况下也是有害元素。使钢产生热脆性，降低钢的延展性和韧性，在锻造和轧制时造成裂纹。硫对焊接性能也不利，降低耐腐蚀性。所以通常要求硫含量小于0.055%，优质钢要求小于0.040%。在钢中加入0.08-0.20%的硫，可以改善切削加工性，通常称易切削钢。四、拉伸试验：屈服点或屈服强度MPa:≥210；抗拉强度MPa:；伸长率%：≥27（标距50mm）
to the steel plate used for . It is used for fixed hull and other .
Type of steel: and low steel plate for S.SA285 are and
: / for and .
steel are in or can be in the state of stop fire or or plus . : hot high etc.Flaw high and high .
3. of five of on steel plate :
A, (C) : in steel yield point and but and . When 0.23%, the of steel will worse. the of low alloy steel used for does not 0.20%.High will also the of high steel in the open field is easy to rust;In can the cold and aging of steel.
B. (Si) : is added in the as agent and so the steel 0.15-0.30% .If steel more than 0.50-0.60% is an . is used in steel it can the yield point and of steel.The of steel can be by 15-20% by 1.0-1.2% .The of and and can the and and make heat steel.Low steel 1-4%, with high used in the as steel sheet.The of will the of steel.
C, (Mn) : In the of is a good and . steel 0.30-0.50%.When 0.70% or more in steel is as " steel". with steel steel not only has but also has and so as to the of steel and of steel. For 16Mn steel is 40% than A3 yield point.Steel 11-14% has high wear and is used for ball mill etc.The of the of steel and the .
D. (P) : In is a in which the cold of makes the the and makes the cold worse. the in steel is to be less than 0.045%, and the for steel is lower.
E, (S) : is also a .It the steel to hot the and of the and and . is also bad for . the is to be less than 0.055% and 0.040% for high steel.The of 0.08-0.20% to steel which is often free steel.
Iv. test
Yield point or yield MPa:≥210;
MPa:;
% : ≥27 ( : 50mm)